190B/190C Series Scopemeter

Ideally suited for engineers, mechanics, field service personnel, students, and all others who do not need the extra expense of an NIST-traceable procedure. Our basic calibration is the same as a certified cal but without traceability. We use the standards and procedures outlined by Fluke for proper, accurate calibration so we can guarantee 100% compliance to the published tolerances. Not suited for ISO-certified facilities, medical uses, or other applications that requires conformance auditing.

Inoperative channels are found most often in instruments over 5 years old that have been sitting unused for several months or more. Symptoms range from erratic readings to blank or missing trace lines. This repair is a flat-rate service based on the number of channels in need of repair and includes our basic calibration, which is required.

Not sure what is wrong with your instrument? Give us a brief description of the problem and we'll check it out for you. Once we determine the cause of the trouble, we will send you a quote for repairs. The evaluation fee is waived if you decide to proceed with the repair. If your instrument cannot be repaired, we will return it at no charge under our "No-Fix, No-Pay" policy (minus return shipping costs).

Problem description is requiredProblem description: 

Having trouble powering or charging your scope? Our flat-rate Power Fault Repair addresses any and all issues related to power failures. Select this service to get you back up and running quickly.

Upgrade your 192B, 192C, 196B, 196C or 199B Scopemeter to a full-featured, 200MHz COLOR 199C! Your Scopemeter is almost there already, you don't need a whole new meter to enjoy all features of the faster, more capable 199. This upgrade makes a 192 or 196 exactly the same as if it were originally a 199C from the factory.

Includes hardware upgrade, firmware update, and basic calibration without a certificate.

Need your instrument back in a hurry? We offer 24, 48, and 72-hour turnaround options with a money-back guarantee. The clock starts ticking from the time we either receive your meter or your acceptance of an official quote, and it stops when it is boxed and ready for shipment. If more than the allotted has elapsed, we will refund the Expedited Service fee.

Conditions:

• For instruments received on Friday after 12:00 p.m., the clock stops at 5:00 p.m. and resumes the next business day at 9:00 a.m. (Central Times).
• For Diagnose & Quote scenairos, the clock starts when we receive your instrument and stops when we send you a quote for repairs. It resumes when we receive your acceptance of the quote.
• If parts are required for any repair that are not in stock, the clock stops when the parts order is placed with the vendor and resumes when the parts are received and checked into inventory.
• "Boxed and ready for shipment" means the instrument is ready for pick-up by the carrier. The carrier will be notified immediately of the shipment. If the carrier does not come or has already come that day, pick-up may not occur until the next business day.
• Return shipping charges are not included in this option.

We highly recommend sending your instrument using a trackable shipping method. If possible, select a method that ensures delivery before noon. You should select a return shipping method during checkout; the default is "Best Way".

The original Fluke NiMH battery for all 190 series Scopemeters. Dependable and ready to work under all conditions, the BP190 is the standard workhorse battery for Fluke's latest Scopemeter lineup. Average run time is 4 hours on a fully charged battery under normal conditions.

A solid performer, this Interstate version of the BP190 meets or exceeds the original Fluke battery in all aspects including lifetime and capacity. Designed as an economical alternative to those not needing the OEM pack, these batteries have a proven track record built on Interstate's attention to quality and detail. We use these in our own instruments and highly recommend them without hesitation. Gives 4 hours of uninterrupted run time on a fully charged battery.

Is your side handle worn or missing completely? Designed for easy single-handed use of your 190-series Scopemeter, these padded handles are comfortable and adjustable to fit your hand perfectly. Velcro straps simply slide through the retainer clips (included) to make for easy size adjustment.

Installation requires opening the instrument case to fit the retainer clips into the slots in the case. Any calibration or warranty labels sealing the case must be broken to perform the installation.

Original input covers for the top of all 190-series Scopemeters. These are great for replacing a marked or broken top cover to make your instrument look new again. Also available is the set of both top and bottom covers.

Give your scope a fresh, clean look with a simple cover replacement. Comes with two combo-torx screws for mounting. Snaps into place with a positive action so you know it is seated.

Complete set of yellow top and bottom covers for the 190-series Scopemeter. Includes two screws for each cover for proper mounting. Great for replacing dirty or damaged covers when intending to sell your meter.

This cover fits all 190-series Scopemeters including the original 190, 190B and 190C models. Includes two combi-torx screws for securing to the front cover. Does not include tilt stand or hanging strap; both may be ordered separately.

Designed as a drop-in replacement for the original keypad contact foil. Recognizing the weaknesses in the OEM foils, we developed our own replacement contact board that is much more substantial than the original Fluke foils. Installation is simple; remove the existing foil and position the new board directly in its place. If you prefer to have us perform the replacement, first add this item to your cart then order the "Diagnose & Quote" service above and put a note in the Comment field requesting the replacement.

Possible symptoms of a defective foil include non-functioning buttons, erratic instrument behavior, or inability to turn the instrument on. In some cases, the instrument may be turned on but no other buttons respond when pressed. Lifetime warranty.

A broken charger jack is a common problem on all 190-series Scopemeters. This jack is proprietary to Fluke; you will not find it at any electronic parts supplier. Most often, the rear pin breaks off due to repeated insertions of the charger plug. The jack is connected to the main PCA only by the solder joint and is not fastened in a solid manner. Thus the jack is allowed to move slightly when the plug is inserted or removed. To overcome this problem and help prevent breakage of the replacement jack, we highly recommend using a bead of hot-melt glue or another liquid adhesive between the jack and the gray input terminal assembly. This will give the jack a firm anchor so the pins do not take the full force of the plug.

A drop-in replacement for scratched or damaged display windows. To replace, the Scopemeter may have to be disassembled if the old window cannot be easily removed from the outside. It is often helpful to first warm the window (especially around the perimeter) to soften the adhesive. Sometimes the old window can be removed by prying the edge with a narrow object, such as a guitar pick. Otherwise, it can be pushed out from the inside after the front cover has been removed. Lifetime warranty.

A broken charger cable is a common problem on all Fluke Scopemeter and Power Quality Analyzer chargers. The plug end is proprietary to Fluke; you will not find it at any electronic parts supplier. Most often, the cable breaks internally near the strain relief due to normal handling and use.