Home > Catalog > 90B/105B Series Scopemeter

90B/105B Series Scopemeter

Repair Services & Replacement Parts

Repair Services

Basic Calibration, Non-Traceable

  • Expired or voided calibration
  • Calibration notice nag message
  • Unstable or inaccurate readings
Ideally suited for engineers, mechanics, field service personnel, students, and all others who do not need the extra expense of an NIST-traceable procedure. Our basic calibration is the same as a certified cal but without traceability. We use the standards and procedures outlined by Fluke for proper, accurate calibration so we can guarantee 100% compliance to the published tolerances. Not suited for ISO-certified facilities, medical uses, or other applications that requires conformance auditing.
Calibration, Basic Non-Traceable $ 95.00  
Your Price $

Diagnose & Quote

  • Power issues
  • Battery charging problems
  • Dark or faint display
  • Waveform unstable
Not sure what is wrong with your instrument? Give us a brief description of the problem and we'll check it out for you. Once we determine the cause of the trouble, we will send you a quote for repairs. The evaluation fee is waived if you decide to proceed with the repair. If your instrument cannot be repaired, we will return it at no charge under our "No-Fix, No-Pay" policy (minus return shipping costs).
Problem description: 
Diagnose & Quote $ 60.00  
Your Price $ 0.00
Replacement Parts

90/105 Keypad Contact Board (except 98)

  • Replaces damaged keypad foils
  • Easy to install
  • Lifetime warranty
  • NOT for model 98
Designed as a drop-in replacement for the original keypad contact foil. Recognizing the weaknesses in the OEM foils, we developed our own replacement contact board that is much more substantial than the original Fluke foils. Installation is easy; just disconnect the old foil and plug in the new board. If you prefer to have us perform the replacement, first add this item to your cart then order the "Diagnose & Quote" service above and put a note in the Comment field requesting the replacement.

Possible symptoms of a defective foil include non-functioning buttons, erratic instrument behavior, or inability to turn the instrument on. In some cases, the instrument may be turned on but no other buttons respond when pressed. Lifetime warranty.

This item is NOT for Scopemeter model 98. The Keypad Contact Board for the 98 Scopemeter is listed below.
90/105 Keypad Contact Board $ 65.00  
Your Price $
17 Available

Interstate PM9086 NiCd Battery Pack

  • Nickel Cadmium
  • 4.8 Volt
  • 2.2 Amp Hour
  • Charging tab for in-meter charging
A tested and proven alternative to the discontinued Fluke PM9086 NiCd battery, these Interstate versions meet or exceed the original battery's specifications in all aspects. Designed as a direct drop-in replacement, these packs have a charging tab for in-meter recharging.

For use in all 90-series and 105-series Scopemeters, including "B" and Series II meters.
Interstate PM9086 NiCd Battery Pack $ 55.00  
Your Price $

90/105 Battery Compartment Cover, USED

  • Fits all 90/105 series Scopemeters
  • Includes screws
Battery compartment cover for all 90-series and 105-series Scopemeters. Includes the two fastening screws. Installation requires a flat or T-10 Torx screwdriver.
90/105 Battery Compartment Cover, Grade A $ 25.00  
Your Price $
1 Available

Fluke 9x/105 Battery Contact Set

  • Nickel plated for durability
  • Minor technical ability required for installation
  • Does not include battery wiring harness
Corroded battery contacts are a common problem that plagues the legacy Scopemeter units. This set of new contacts includes the charging terminal in the bottom of the compartment. Electroplated with nickel, these contacts will resist corrosion and wear for many years. Set of (4) battery contacts and (1) charging contact. Instructions are not included at this time.
90/105 Battery Contact Set $ 65.00  
Your Price $

Fluke Charger Cable

  • Fits all Scopemeter and Power Analyzer chargers
  • Genuine, original Fluke charger cable
A broken charger cable is a common problem on all Fluke Scopemeter and Power Quality Analyzer chargers. The plug end is proprietary to Fluke; you will not find it at any electronic parts supplier. Most often, the cable breaks internally near the strain relief due to normal handling and use.
Fluke Charger Cable $ 30.00  
Your Price $
2 Available